Beginner's Plumbing: The Essentials for Bathtub Installation

Call Today

What are your thoughts about Tools You Need to Install a New Bathtub ?


How to Install a Bathtub
Mounting a bathtub isn't precisely rocket science, but it does require strong plumbing, woodworking, and often, tiling skills. Changing an old bathtub with a new one is additionally a reasonably difficult job. If the old tub is easily easily accessible, the job can move speedily; if you have to open up a wall surface to remove the old bathtub as well as place the brand-new bath tub, the task is much harder. In either instance, the job is within a home handyman's abilities, although you will certainly require an assistant to leave the old bathtub as well as embeded in the new one. See to it you have certified yourself for the job and also are comfortable trying it. Instead of hiring a specialist to take control of a halfway-completed task, it is much better to think about employing one before you start. Possibilities are you might need a professional plumber to make tube connections.
This short article will help you set up a brand-new bathtub in your bathroom if you have already gotten a brand-new tub and don't require to change the setup of your previous water pipes.
Your tools and also material checklist should consist of the following:
  • New Bath tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipe Caps


  • Preparing for the Installation


    To start with, the supporting structure supplied with the bathroom must be fitted (if called for) according to the producer's directions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is important to make sure that if the faucet comes with a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets unit to prevent strain on the tub.
    Fit the flexible tap ports to the bottom of the two faucets using 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you utilize every one of the provided washing machines.
    Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom must now be ready to be fitted in its final placement.

    Removing Old Touches


    If you require to replace old faucets with new ones as a part of your installation, then the first thing you need to do is separate the water. After doing so, switch on the taps to drain any water continuing to be in the system. The procedure of removing the existing faucets can be fairly problematic because of the limited access that is commonly the situation.
    Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a towel prepared for the staying water that will originate from the pipes. As soon as the supply pipes have actually been gotten rid of, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from transforming during this process. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old sealing substance.
    Before moving on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.

    Mounting the Bath tub


    Making use of both wooden boards under its feet, put the tub in the needed setting. The wooden boards are handy in equally spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto four little points.
    The next objective is to guarantee that the bathtub is leveled all round. This can be attained by examining the spirit level and adjusting the feet on the bathtub till the level reviews degree.
    To set up taps, fit all-time low of the furthest versatile faucet port to the proper supply pipeline by making a compression sign up with; after that do the very same for the other tap.
    Switch on the water supply and check all joints and brand-new pipework for leakages as well as tighten them if needed. Load the tub and also examine the overflow electrical outlet and also the typical outlet for leakages.
    Lastly, deal with the bath paneling as defined in the maker's instruction manual. Tiling and securing around the bathtub must wait up until the bath tub has actually been made use of a minimum of when as this will certainly resolve it right into its final setting.

    Suitable New Taps


    If the tails of the new faucets are plastic, after that you will certainly require a plastic connector to avoid damages to the string. One end of the port fits on the plastic tail of the faucet and also the various other end provides a link to the existent supply pipes.
    If you require to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
    Next, position the faucet in the mounting hole in the bath/basin making sure that the washers are in area between the tap and the sink. Secure the tap in position with the maker offered backnut. When the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal tap adapters. The former kind must be connected to the faucet finishes first, tightening up just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.

    Tiling Around the Bathtub


    In the area where the bathroom fulfills the ceramic tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the fitting can move sufficient to break an inflexible seal, triggering the water to penetrate the wall in between the bath and the tiling, causing complications with moisture and also possible leaks to the ceiling below.
    You can select from a range of coloured sealants to blend in your components and also fittings. They are sold in tubes and also cartridges, and are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with spins of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water before sealing, to enable the activity experienced when the bathtub remains in usage. The sealant can fracture relatively very early if you do not take into account this movement prior to securing.
    Conversely, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly offered on the marketplace. It is a good idea to fit the tiles using waterproof or water-proof glue and also cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub

    Do you appreciate reading up on Tools You Need to Install a New Bathtub ? Make a remark down the page. We will be interested to know your feelings about this content. We are looking forward that you visit us again in the near future. Sharing is caring. Who knows, you may very well be doing someone a favor. Thanks for your time. Kindly come visit our site back soon.


    Immediate relief, just a call.

    Leave a Reply

    Your email address will not be published. Required fields are marked *